by Todd Walker
On a modern homestead wood lot, one cranks a chain saw, cuts logs to the length, and splits the rounds to season. The motorized saw makes quick work of large and small wood. But in an operational base camp, lugging a chainsaw, bar oil and fuel, on a regular basis is not practical. A good ax weighs less but can get the job done. However, there are challenges to cutting firewood (not splitting) to length with an ax.
Here’s a simple solution which not only saves your ax bit from grit and rocks in the ground, but allows you to use a powerful vertical chopping stroke safely – described in our last ax work article. To cut a winter supply of firewood with an ax only, take the time to build this speedy chopping platform.
The Ax Chopping Platform
Adapted from The Ax Book (D. Cook)
Here’s what you’ll need to build your own…
- 2 Base Logs – six to seven-foot hardwood logs about 10-12 inches diameter
- Stop Stick – 5 inches diameter by one foot
- Sturdy, heavy gauge wire
- Ax, of course
- Saw – chainsaw will speed up your project
- Pliers for twisting and cutting wire
- Hardware – 4 nails, 3 feet of cable or chain
- 5 pound weight
Step 1: Cut Base Logs
For axmen, chop down a hardwood tree with your felling ax. Buck it twice to get two 7 foot lengths. Or crank your chainsaw for the task. Either way works.
I chose a half-broken Sweet Gum (Liquidambar styraciflua). City folk hate them in their yards due to their pesky, prickly fruit, a scourge on bare feet and medieval projectiles when mowed. Trash trees in the view of many. But very resilient.
Now for the fun part… getting them back to camp. My good friend, Cokey, pork-butt-smoker extraordinaire, speaking in full southern drawl, always has this to say about any hard work,
“It’s like haulin’ logs. Ya gotta really wanna do it.”
And I did. I flopped and rolled my two sticks, dodging trees and obstacles, back to camp. My peavy was a fine companion to have along the journey.
Step 2: Secure Base Logs
For the sake of clarity, the end of the platform where the chopping happens we’ll call the “Head“. The opposite end of the platform will be, you guessed it, the “Tail“.
Position the two logs side-by-side so the fat end of one mates up with the skinny end of the other. This will form the trough to hold the long wood you plan to chop into smaller wood. It’s a good idea to lay two length of cedar, or other rot resistant wood, perpendicular at the ends of the logs to keep them off the ground. This also makes the wiring job you’re about to do much easier, i.e. – passing wire under two real heavy logs.
Your choice in wire matters. In my video, the electric fence wire couldn’t stand the pressure. I cut lengths of rusty, but still strong enough, barbed wire from a fallen hog wire fence line near base camp. Be resourceful.
Wrap the wire around the Head of the platform and twist tight with pliers. You could also use a stout stick as a windlass. Beat the exposed barbs down if you use wire in the barbed variety.
Mr. Cook illustrates three wooden dowels driven through the two logs horizontally. If you’re building this project at your homestead, that may be feasible. Or, just drill and run all-thread rods through and secure with nuts and bolts. In the woods, I used the simple method, wire.
Step 3: Secure the Stop Stick
Butt the stop stick against the newly installed wire crossing the trough. Twist it down until taut. Too much twisting and you’ll sheer the wire and have to start over. Fencing pliers come in handy but other pliers work. Another option would be to use a Spanish windlass to tighten the wires. Ted, a member of our Doing the Stuff Network, pointed me to the Cobb & Co Hitch method.
Step 4: Attach Front Kickback Guard
If you’ve ever had a wooden missile fly at your face while chopping through a horizontal stick, you’ll appreciate the importance of this step. A whole lot of pain accompanies a stick in the eye. To prevent this stick-to-the-face event, install a piece of domed wire 6 to 8 inches past the stop stick.
I cut a section of that old hog wire long enough to arch over the platform creating a two-square wide hood of sorts. It hugs the top of the stop stick with about 6 inches overhanging the platform logs. I used two 16d nails and washers to secure the four ends to the sides of the platform logs. This gives me enough room to chop firewood lengths while safeguarding my noggin from flying firewood.
Step 5: Install Rear Kickback Guard
As experienced wood lot choppers know, as the stick you’re chopping to size shortens, especially the final two short lengths, the butt end is free to fly, and often does. Another kickback guard will hold the last length in the trough. However, this rear guard can’t be secured permanently over the trough or the stock your chopping won’t rest flat between the platform logs.
Screw or nail a section of chain or wire to the chopping side of the platform with a weight attached to the end of the chain. This will allow you to toss the restrain over the stock in the trough as it shortens.
The distance between the front and rear kickback guards depends on the length of firewood you need. For instance, at base camp, 18 to 20 inches is about right. Mark the trough at your desired length. From that mark, attach the rear guard about the same distance as the front guard towards the Tail end of the platform.
On a homestead, any metal 5 pound weight can be located to hold the rear guard in place. In the forest, not so much. I stole a jagged-edged rock from my fire pit, wrapped it with wire, and attached it to the end of my chain restraint. When engaged (flopped over the logs), the weight rests about midway down the opposite side of the platform.
Step 6: Wire and Notch the Tail
To wire the Tail, cut a 90 degree notch in the end of both logs. The depth of the vertical cut should be slightly past the depth of the trough. Now cut horizontally to meet the vertical cut and remove the notch and create a ledge. Wrap wire around the log ledge and twist taut. If you run the wire tight in the corner, you’ll have a small, horizontal “table top” to sit your hot cocoa while sitting on the platform around the campfire. Flat horizontal surfaces are a luxury at base camp.
Step 7: Get to Chopping
Green wood is easier to chop than seasoned. Both are easier to separate when chopped at a 45 degree angle to the grain. Feed your stock into the trough up to the stop stick. Position yourself at a 45 degree angle where you can make a full vertical, backed-up stroke in the trough on your marked chopping spot. The stock is easily separated with a single, well placed stroke. On thicker stock that doesn’t, rotate the stick in the trough and chop it once more. That ought to do it.
Remember to “engage” the rear guard as the butt end of the stock shortens and gets itchy to jump off the platform.
The Axe Cordwood Challenge
In our Ax Chopping Platform video, I mentioned Steven Edholm’s “Axe Cordwood Challenge” on his YouTube channel, Skill Cult. Some may be wondering, why in the world would a person chop a cord of firewood, a stack measuring 4’x4’x8′, with an ax only?! They’re still manufacturing chainsaws, ya know! They do indeed. I own a couple of these modern marvels.
But, the ax, a simple machine, unlike the chainsaw, requires minimal field maintenance. Granted, the chainsaw cuts firewood to length quicker than an ax. To accommodate modern cutting, you’ll need to haul the gas-oil-mix can, bar/chain oil, an extra bar and chain for saws stuck in a log, and other field maintenance tools. You’ll probably carry an ax alongside the motor saw as a backup anyway. But with modern means of travel, four-wheelers and trucks, that’s not a huge deal.
Here’s the thing, for me at least…
In my mind, more significant is the fact that ax-manship is an old-soul skill which few moderns wish to re-kindle, never seeing the possibility of a future dependent on axes to stay warm. It is neither convenient nor easy. However, ax work is my most personally rewarding, satisfying, and warming undertaking I’ve done over the years.
You find an axman, one who turns a tree into firewood by felling, limbing, bucking, splitting lenght-wise for hauling, and then, chopping wood to length, and he’ll confirm that the most challenging job of staying warm with his ax is chopping to final burning size. This chopping platform greatly increases the speed, safety, and efficiency of making long logs short.
So, Steven, I’m taking you up on your challenge. Updates will be posted on my progress. If nothing else, I’ll be in great shape from swinging steel and hauling logs.
Keep Doing the Stuff of Self-Reliance,
P.P.S – If you find value in our blog, Dirt Road Girl and I would appreciate your vote on Top Prepper Sites! You can vote daily by clicking here or on the image below. Check out all the other value-adding sites while you’re there…
Thanks for Sharing the Stuff!
Copyright © by Survival Sherpa: In light of the recent theft of all my content by a pirate site, my sharing policy has changed. I do not permit the re-posting of entire articles from my site without express written consent by me. My content on this site may be shared in digital form (200 words or less) for non-commercial use with a link back (without no-follow attribute) to the original article crediting the author. All photos, drawings, and articles are copyrighted by and the property of Survival Sherpa. You are more than welcome to share our photos and articles on social media for educational purposes as long as you link back to the original article/photo with credit to the author.