by Todd Walker
I stand in countless hardware stores mumbling my frustration… “can I get a double bit ax handle, please!?”
Finding a suitable handle for a double bit ax restoration project is like searching the proverbial haystack for that lost needle. It’s a horrible waste of time. I could have ordered a handle from a few U.S. ax handle suppliers. But I’d never made my own ax handle.
Mike, our across the street neighbor and good friend, had a large hickory snap in a recent storm. I loaded my chainsaw and wood cutting tools into our garden wagon, pulled into his yard, and cut the fallen tree into firewood lengths.
One four-foot section at the base of the tree had spit down the middle in the fall. For some reason, I didn’t cut these two split sections into firewood. A few weeks later I’d understand why…
Mike was taken from us. The unexpected, sudden loss of his life nudged me into action. The two uncut sections eventually made their way to my backyard for a labor of love.
Before the ingenious Paleo person came up with the idea of lashing a stick to a sharp stone, people simply palmed axes in their hands to chop stuff. The invention gave primal man leverage and a powerful mechanical advantage needed to work more efficiently. Later, in the Iron Age, this idea changed the course of human history when wooden handles were attached to metal cutting tools. Doing the Stuff of Self-Reliance just got easier!
To make your own ax handle, here’s some stuff you’ll need…
Tools and Material
- A Tree ~ Hickory was available so I used it. Other suitable trees include ash, white oak, sugar maple, or hornbeam (ironwood). A tree with a diameter of at least 10 inches with straight grain will give you the best chance at finding a billet to use.
- Wedge(s), Sledge Hammer, and/or Spitting Maul ~ A metal wedge is used to split the round into quarters. A splitting maul can be used if you don’t own a wedge. Wooden wedges can be used after the initial split in the log.
- Ax or Hatchet ~ Used to cut the rough shape of the handle.
- Draw Knife ~ Refines the shape
- Rasp ~ For removing detailed amounts of wood
- Shaving Horse ~ Holds stock in place while working the draw knife or rasp. A bench vise will also do the job.
- Wooden Maul ~ Hitting stuff
- Pencil and Measuring Device ~ You’ll do a lot of drawing and measuring
- Fine-Toothed Saw ~ Cutting the slot to accept the wedge and cutting handle to length. I used my Japanese saw from my carpenter’s tool kit.
- Sand Paper – 80 and 150 grit
Here are the steps used to make my handcrafted hickory handle which holds sentimental value.
Step #1: Split the Log
Lay the log on flat ground. My log was already halved when it fell. With a full round, drive a wedge in the top of the log to start a split down the middle of the wood. Continue the split with another wedge or splitting maul. Once separated, use an ax to cut any wood fibers holding the two pieces together.
Lay the half on the ground (flat side down) and split it into two quarters. Depending on the size of your log, you may need to cut quarters into eighths. Now you have billets with about 4 to 6 inches of bark on the outside of the wedged-shaped wood.
Step #2: Find a Handle
Look at the end of the billets and select one with annual growth rings that run straight through the length of your handle. Avoid billets that have twists and defects (knots).
Draw a 1.5 x 5 inch rectangle on the end of the billet with the growth rings running as straight through the length of the rectangle as possible. The closer the growth rings are to each other the stronger the handle will be.
Stand the billet on end and score one of the long rectangle lines with an ax and wooden maul to start a split. Remove the ax and finish the split with a wedge. Repeat the process for the remaining lines on the rectangle. If all goes well, you’ll have a piece of stock in a rough rectangular shape.
Step #3: Hew the Handle
Stand the billet on a wooden anvil at a slight angle. Begin hewing the form of the handle. Score down the length of the handle in 1 to 2 inch spacing with a sharp ax or hatchet. Then go back and remove the score marks with controlled chopping/slicing motion of the ax. This technique is safely done by chopping with the ax perpendicular to the wood anvil.
Work down the billet on all the sides until you have a rough shaped handle. Remember that you can’t add wood back once it’s removed. But the more you take off in this step, the easier your job will be in our next step.
Step #4: Refine the Handle
Sketch an outline of handle shape on the roughed handle. Place the stock in a shaving horse or some type of vise that will hold securely.
Begin shaving off the wood that isn’t the handle (outside the lines). A sharp draw knife is essential. Go with the grain to remove material. If the knife digs into the stock at a sharp angle, you’re going the wrong way. Turn the handle around and work the grain the other way.
Leave the handle portion that fits in the eye of the ax as a rough shaped rectangle for now. Concentrate on material removal on the shaft. The shaft should begin to take the shape of an oblong handle with narrow edges that run the same plane as the ax bit(s). The wider sides of the shaft help prevent the handle from turning in your hand when using the cutting tool.
Step #5: Rasp Time
Once the shaft is close to your finished size, begin removing wood from the head end with a draw knife. Check the size needed by placing the ax head against the end so that it is about a 1/4 inch larger that the ax eye. Place the axhead against the end and draw a line from the inside of the ax eye.
Secure the handle and begin removing wood from the head with a rasp. Get the head close to size and try fitting the axhead on the handle. If it goes on the tip of the head, tap the butt of the handle with a wooden mallet or maul until the axhead stops moving on the handle. You’ll hear a ringing sound instead of thud once it’s seated.
Remove the axhead from the handle. You’ll see marks on the head showing you how much more wood needs to be removed for a proper fit. Rasp more off the head end and check the fit again. Take your time and remove small amounts of wood until the axhead fits down to the shoulder of the handle with at least a 1/4 inch sticking out of the top of the ax eye.
To remove the axhead from the handle, I carved another piece of hickory slightly smaller than the ax eye but larger at the opposite end to be used as a punch. Place the axhead on a raised platform so that the handle is off the ground. I used my shaving horse for this task. Drive the handle out of the eye with the wooden punch and hammer or wood maul. You’ll do this procedure several times while testing the fit.
With the axhead removed, begin shaping the shaft and head of the handle with your rasp.
Step #6: Sand the Handle
With the handle close to size, begin sanding to smooth the surface. I began using a broken 42 inch 80 grit sanding belt by hand. I eventually switched to my orbital sander with 80 grit paper to speed up the process. 150 grit finished the handle.
Step #7: Cut Slot and Wedge
With a fine edged saw, cut a slot in the head end of the handle about half the depth of the ax eye. I used a piece of scrape leather in my bench vise to prevent marring the sanded handle. Japanese saws are excellent for fine, clean cuts. They cut on the pull stroke.
Make a wedge from a scrap piece of wood. I used a piece of seasoned Tulip Poplar in my shop. The grain orientation of the wedge ran perpendicular to the grain of the handle.
Step #8: Hang the Ax
Time to hang the ax on the finished handle. You should be good at this by now. Whack the butt of the handle with a maul while holding the handle in a vertical position. Smack the butt until you hear that solid ring when the axhead seats on the shoulder.
Trim any curls off where the ax eye and shoulder bottom out. Check the alignment of the head on the handle by sighting down the handle towards the bit of the ax. The center line of the handle should line up with the ax bit. If not, remove the ax and sand wood from either side to achieve alignment.
When everything is in line, drive the wedge into the slot on top of the handle. Add a little wood glue to the wedge. The wedge, properly seated, will expand the top of the handle in the eye to secure the axhead to the handle. Cut the wedge off with a saw and sand the end until 1/8 to 1/4 inch of handle is sticking out of the axhead.
I cut this straight handle at 29 inches. This is a good length for the 3 pound Warren Axe and Tool double bit ax. It’s a custom handle that feels good in my hands. That’s all that really matters.
Step #9: Oil the Handle
Apply a coat of boiled linseed oil to all the exposed wood. Repeat this application daily for one week. Then once a week for a month, and once a month for a year.
My next project is to make a double bit sheath for this special ax. I’ll let you know when it’s done. Nothing beats making stuff with you own hands!
Keep Doing the Stuff of Self-Reliance,
P.S. – You can also keep up with the Stuff we’re Doing on Twitter, Pinterest, Google +, YouTube, Instagram, and Facebook… and over at the Doing the Stuff Network.
P.P.S – If you find value in our blog, Dirt Road Girl and I would appreciate your vote on Top Prepper Sites! You can vote daily by clicking here or on the image below. Check out all the other value-adding sites while you’re there…
Thanks for Sharing the Stuff!
Copyright: Content on this site (unless the work of a third-party) may be shared freely in digital form, in part or whole, for non-commercial use with a link back to this site crediting the author. All links in articles must remain intact as originally posted in order to be republished. If you are interested a third-party article, please contact the author directly for republishing information.