by Todd Walker
Dirt Road Girl wanted something substantial to cage her tomatoes in our front yard. She hates those flimsy wire cages. Our backyard is full shade. We followed the sun and started food-scaping the font yard. There’s sunshine 8 hours a day out front.
She wanted something functional, sturdy, and of course, homemade. I made rolled wire cages last year from fencing. One problem with these cages was that they blew over during summer storms – even after staking them down in the container. We needed something anchored into the ground.
We had an old wooden ladder by my shop. I suggested we use it as a ‘cage.’
“That’ll work!”
Here’s what she came up with… for me to do!
Todd’s Tomato Ladder is not your typical tomato cage.
After a quick search online, she drew inspiration from Mother Earth News – Woody’s Folding Tomato Cages.
Keep in mind that these tomato ladders are going in our front yard. I printed Woody’s plans, gather lumber, and set to building. He calls for using 8 foot 1×3 lumber for the legs. I go to work.
8 foot tomato ladders are 2 feet shy of a regulation basketball goal.
It never occurs to me that erecting two “twin tower” tomato ladders in our front yard might draw neighbor’s ire. We try to fly under the radar as much as possible in our front yard food-scaping. These 8 footers would work in the country or a backyard.
I quickly build two of these bad boys, set them over the containers, and think, “wow, those sure are high.”
Painting your house, Walker?
They lasted about a week after we noticed neighbors walking by with thought bubbles over their heads…
“What are they up to this year!?!”
Back to the drawing board.
I needed to shrink Woody’s plans.
Here’s the plan if you want to build our 6 foot model.
Bill of Material
Use non-pressure treated lumber to keep chemicals from leaching into your plants.
Four 1 x 3 boards 8 feet long
Two 1 x 2 boards 8 feet long
10 1/2 inch piece of 2 x 4 lumber
About 40-50 1 5/8 inch screws (I use star drive decking screws. It’s my personal mission to convert everyone to superior star drive screws)
Four 3 inch decking screws (2 will be used to attach the 2 x 4 to the legs – 2 will be used to attach the base of the legs to ground stakes)
Tools List
Circular Saw – If you’ve got a miter saw, it makes quick work of the cutting chores. But a circular saw will do the job.
Drill/Impact Driver
Hammer (for driving anchor stakes in the ground)
1/8 inch drill bit
Tape measure
Pencil
Skill Level
Beginner
Time Needed
30 minutes per ladder (that’s a generous estimate)
Cut List
1. Cut four 1 x 3’s six-foot long.
2. Cut one piece of 2 x 4 scrap 10 1/2 inches long.
3. Cut the 1 x 2’s for the rungs of the inside legs – working from the bottom of the ladder to the top: 19 1/2 inches, 17 1//4 inches, 15 1/2 inches, 13 3/4 inches, and 12 1/4 inches.
4. Cut the 1 x 2’s for the rungs of the outside legs – working from the bottom to the top: 21 inches, 19 inches, 17 inches, 15 1/4, and 13 3/4.
5. Cut two 1 x 3’s twenty inches long (use the extra two feet cut from the leg pieces). These will be the cross braces on the legs.
Putting it all together
If you don’t want to cut all your material ahead of time, that’s perfectly fine. Pre-cutting will streamline your build and save time.
Step 1: Stack two of the 6 foot 1 x 3 inch legs with the ends flush. Drill a pilot hole through one end of the boards with the 1/8th inch drill bit in the center of the 1 x 3 about 3/4 of an inch from the end of the board. This is where you will insert a 3 inch screw into the piece of the 2 x 4 in a moment. Repeat the process with the two remaining 6 foot 1 x 3 legs.
Step 2: With two of the legs stacked flush, screw a three-inch screw through the pilot hole into the end of the 10 1/2 inch piece 2 x 4 stock. The ends of the 1 x 3’s need to be flush and centered (meaning about 1/4 inch of 2 x 4 exposed on either side of the 1 x 3) on the end of the 2 x 4. Don’t over sink the screws or you’ll spit the wood. Then attach the other two legs to the other end of the 2 x 4. This will serve as the top of the ladder and pivot point for the legs.
Step 3: Go ahead and drill pilot holes in each end of the rungs. Attach the bottom rung (19 1/2 inches) with one 1 5/8 in. screw per side – one foot from the bottom on the inside legs. Continue attaching rungs – longest to shortest – up the ladder with one foot spacing. Now, flip the ladder over and repeat the process for the outside legs starting with the 21 inch rung.
Step 4: With the rungs attached evenly, open the ladder and stand it up. Connect the 20 inch braces to the sides of the ladder. I attached mine at the second rung from the bottom. You can adjust the width of the ladder by moving the braces up for a wider base or down to make the ladder more narrow.
Step 5: Place the tomato ladder over your tomato plant. Drive a pointed wooden stake in the ground beside two legs catty-corner style. Screw the legs into the stakes to anchor them securely.
After the growing season, simply take one screw out of each brace, unscrew the legs from the ground stakes, and fold the tomato ladders up for storage. Or move them into your greenhouse for the winter growing season.
Note: I cut two feet off the top of our original “twin tower” tomato ladders to keep neighborly busy-bodying to a minimum. Here’s the finished product.
Four of Todd’s Tomato Ladders anchored and ready with an old wooden ladder on the far left.
Friends don’t let friends use lame tomato cages! What’s your best method of caging tomatoes?
Here’s a non-related byproduct of building these tomato ladders…
My fly rod and this largemouth bass ended my Saturday on a great note!
Keep Doing the Stuff,
Todd
P.S. – You can also keep up with the Stuff we’re Doing on Twitter, Pinterest, Google +, YouTube and our Facebook page… and over at the Doing the Stuff Network on Pinterest, Google +, and Facebook.
P.P.S – If you find value in our blog, Dirt Road Girl and I would appreciate your vote on Top Prepper Sites! You can vote daily by clicking here or on the image below. Check out all the other value-adding sites while you’re there…
Thanks for Sharing the Stuff!
Copyright © by Survival Sherpa: In light of the recent theft of all my content by a pirate site, my sharing policy has changed. I do not permit the re-posting of entire articles from my site without express written consent by me. My content on this site may be shared in digital form (200 words or less) for non-commercial use with a link back (without no-follow attribute) to the original article crediting the author. All photos, drawings, and articles are copyrighted by and the property of Survival Sherpa. You are more than welcome to share our photos and articles on social media for educational purposes as long as you link back to the original article/photo with credit to the author.
Survival Sherpa 